00:00:11:18 - 00:00:18:12 Unknown In this video, we're going to show you how to operate our field mixers using a shotgun microphone mounted on a boom pole. 00:00:18:14 - 00:00:38:17 Unknown The following items should be a part of your bundle. A shotgun microphone, two XLR cables, a 2 or 3 channel field mixer. You will also need to bring your own three AA batteries, two pairs of headphones, and quarter inch adapter. 00:00:38:19 - 00:00:44:14 Unknown First we'll set up our boom. Check if your shotgun microphone has any batteries inside and remove them. 00:00:44:16 - 00:01:00:05 Unknown We will be powering our microphone by Phantom Power instead. If your shotgun mic has a switch for battery on and off, select off. Set up the microphone in the shock mount and connect the XLR cable. 00:01:00:07 - 00:01:04:17 Unknown Make sure to extend the pole from the top for optimal weight distribution. 00:01:04:19 - 00:01:11:15 Unknown Wrap the cable around the boom pole. 00:01:11:17 - 00:01:16:20 Unknown For proper mic placement, aim your microphone at your subject’s chest. 00:01:16:21 - 00:01:22:09 Unknown Now we'll go over the operations of our field mixers. These Sound Devices mixers are battery powered. 00:01:22:11 - 00:01:27:21 Unknown For the two channel mixer, unscrew the silver cap and take out any existing batteries. 00:01:27:23 - 00:01:34:14 Unknown Insert your two AA batteries, noting the positive and negative end placement. 00:01:34:16 - 00:01:41:21 Unknown Close the cap to secure the batteries. For the three channel mixer, you will need three AA batteries. 00:01:41:22 - 00:01:48:08 Unknown To power on the mixer, locate the power switch on the front panel and select ‘INT’. 00:01:48:10 - 00:01:55:01 Unknown Now we'll begin to connect our audio source to the mixer. Since this is a condenser microphone, we'll be using phantom power. 00:01:55:03 - 00:02:09:19 Unknown Connect the XLR to the first mic input found on the left side of the mixer. If you are using a second audio source, you could connect it to the second slot. Since this is a condenser mic, ensure that 48 Volt is engaged. 00:02:09:22 - 00:02:12:08 Unknown Move the switch to the left position. 00:02:12:09 - 00:02:16:17 Unknown For the three channel mixer. You can connect up to three sources. 00:02:16:19 - 00:02:27:14 Unknown When using the microphone, change the MIC/LINE input to MIC. Select PH. Engage 48 Volt switch on the far right side of the panel. 00:02:27:16 - 00:02:31:19 Unknown Next, turn to the front panel of the mixer to set our output settings. 00:02:31:21 - 00:02:54:07 Unknown We will assign our ‘Microphone One’ to an output using the LCR switch beside the Mic One knob. We are sending this microphone’s output signal to one side of the camera's two channels. In this example, we'll set it to L. If you are using a second audio source, you would use the same switch for mic two to change the path of that microphone’s output signal. 00:02:54:09 - 00:03:19:15 Unknown It is a best practice to separate microphones into different output paths. Engage the 80Hz or 160Hz High Pass Filter depending on your talent’s voice. Press in the HPF enable switch until the LED light is illuminating your desired setting. You can engage the limiter by selecting ‘LIM’ on the limiter engage switch. Connect your mixer’s headphones for monitoring. 00:03:19:15 - 00:03:21:03 Unknown On the two channel mixer, 00:03:21:04 - 00:03:28:01 Unknown use the quarter inch jack. 00:03:28:03 - 00:03:34:07 Unknown On the three channel, use the 3.5mm or one eighth mini jack. 00:03:34:09 - 00:03:38:12 Unknown On the right hand side of the mixer, we can send our signals to the camera. 00:03:38:14 - 00:03:43:08 Unknown Use the XLR to connect the output of your mixer to the input of your camera. 00:03:43:10 - 00:03:52:14 Unknown We only have one source of audio panned to one side. We will connect from the left output of the mixer to the channel one input of the camera. 00:03:52:16 - 00:03:58:15 Unknown Set the output level to match your recording device. In our case, select ‘LINE’. 00:03:58:17 - 00:04:06:22 Unknown Now adjust your camera settings accordingly. Please ensure that the camera operator is wearing headphones to monitor the sound. 00:04:07:03 - 00:04:11:16 Unknown Before we can begin any recording, we need to calibrate our mixer to the camera. 00:04:11:18 - 00:04:19:07 Unknown On the two channel mixer, locate the slate switch on the front panel and select the left option for sine wave (~). 00:04:19:09 - 00:04:34:23 Unknown At this point, you should hear a tone and your level meter should be illuminated to 0 VU. On the three channel, this switch will say MIC 1K. Switch the option to one kilohertz for the tone. Using your camera's input level controls, 00:04:35:00 - 00:04:40:01 Unknown adjust the input so that the levels of the tone on your mixer are aligned with your cameras. 00:04:40:03 - 00:04:51:07 Unknown Set your levels between -20 and -10dB below the maximum. If your camera does not display a level indicator, set your levels around two thirds of the maximum. 00:04:51:09 - 00:04:55:05 Unknown Once you have calibrated your camera's levels, turn off the tone by switching 00:04:55:05 - 00:04:56:16 Unknown the slate knob back. 00:04:56:18 - 00:05:21:17 Unknown Aim your microphone properly at your subject. Use the Input Gain control on the front of the mixer to adjust the microphone’s levels. Adjust until the average peak level is around zero. For the three channel mixer, put the white knob - the channel fader - to unity. Press the black gain knob so that it pops out. Adjust until the average peak level is around zero. 00:05:21:19 - 00:05:31:10 Unknown When you're done adjusting, press the gain knob back in. While filming, you can fine tune the levels using the channel fader. 00:05:31:12 - 00:05:46:14 Unknown Underneath the gain meter, there are two knobs. Left is the monitor source and right is headphone levels. Choose your source with the monitor knob to make sure you're outputting desired sound to the headphones. In our case, we select L. 00:05:46:16 - 00:05:53:00 Unknown After you've set the gain, you can adjust the headphone levels on the right to control the playback volume. 00:05:53:02 - 00:05:58:03 Unknown If you have any further technical questions, please refer to Production Staff and we'll be happy to assist you. 00:05:58:04 - 00:05:59:08 Unknown Thank you for watching.